System Administration Commands ntpd(1M) NAME ntpd - Network Time Protocol daemon Version 4 SYNOPSIS /usr/lib/inet/ntpd [-46aAbdDgLmnNqvx] [-c conffile] [-f driftfile] [-k keyfile] [-l logfile] [-p pidfile] [-P priority] [-r broadcastdelay] [-s statsdir] [-t trustedkey] [-U interface_update_time] DESCRIPTION The ntpd program is an operating system daemon that syn- chronises the system clock with remote NTP time servers or local reference clocks. It is a complete implementation of the Network Time Protocol (NTP) version 4, but also retains compatibility with version 3, as defined by RFC 1305, and versions 1 and 2, as defined by RFC 1059 and RFC 1119, respectively. How NTP Operates The ntpd program operates by exchanging messages with one or more configured servers at designated intervals ranging from about one minute to about 17 minutes. When started, the pro- gram requires several exchanges while the algorithms accumu- late and groom the data before setting the clock. The ini- tial delay to set the clock can be reduced using options as described in the server options page at file:///usr/share/doc/ntp/confopt.html. When the machine is booted, the hardware time of day (TOD) chip is used to initialize the operating system time. After the machine has synchronized to a NTP server, the operating system corrects the chip from time to time. During the course of operation if for some reason the system time is more than 1000s offset from the server time, ntpd assumes something must be terribly wrong and exits with a panic mes- sage to the system log. If it was started via SMF, the ntp service is placed into maintainance mode and must be cleared manually. The -g option overrides this check at startup and allows ntpd to set the clock to the server time regardless of the chip time, but only once. Under ordinary conditions, ntpd slews the clock so that the time is effectively continuous and never runs backwards. If due to extreme network congestion an error spike exceeds the step threshold (128ms by default), the spike is discarded. However, if the error persists for more than the stepout threshold (900s by default) the system clock is stepped to the correct value. In practice the need for a step is extremely rare and almost always the result of a hardware failure. With the -x option the step threshold is increased to 600s. Other options are available using the tinker SunOS 5.11 Last change: 12 Apr 2007 1 System Administration Commands ntpd(1M) command as described in the miscellaneous options page at file:///usr/share/doc/ntp/miscopt.html. The issues should be carefully considered before using these options. The maximum slew rate possible is limited to 500 parts-per-million (PPM) by the Unix kernel. As a result, the clock can take 2000s for each second the clock is outside the acceptable range. During this interval the clock will not be consistent with any other network clock and the sys- tem cannot be used for distributed applications that require correctly synchronized network time. Frequency Discipline The frequency file, usually called ntp.drift, contains the latest estimate of clock frequency. If this file does not exist when ntpd is started, it enters a special mode designed to measure the particular frequency directly. The measurement takes 15 minutes, after which the frequency is set and ntpd resumes normal mode where the time and fre- quency are continuously adjusted. The frequency file is updated at intervals of an hour or more depending on the measured clock stability. Operating Modes The ntpd daemon can operate in any of several modes, includ- ing symmetric active/passive, client/server broadcast/multicast and manycast, as described in the Asso- ciation Management page at file:///usr/share/doc/ntp/assoc.html. It normally operates continuously while monitoring for small changes in frequency and trimming the clock for the ultimate precision. However, it can operate in a one-time mode where the time is set from an external server and frequency is set from a previously recorded frequency file. A broadcast/multicast or manycast client can discover remote servers, compute server-client propagation delay correction factors and configure itself automatically. This makes it possible to deploy a fleet of workstations without specifying configuration details specific to the local environment. By default, ntpd runs in continuous mode where each of pos- sibly several external servers is polled at intervals deter- mined by an intricate phase/frequency-lock feedback loop. The feedback loop measures the incidental roundtrip delay jitter and oscillator frequency wander and determines the best poll interval using a heuristic algorithm. Ordinarily, and in most operating environments, the state machine will start with 64s intervals and eventually increase in steps to 1024s. A small amount of random variation is introduced in order to avoid bunching at the servers. In addition, should a server become unreachable for some time, the poll interval is increased in steps to 1024s in order to reduce network SunOS 5.11 Last change: 12 Apr 2007 2 System Administration Commands ntpd(1M) overhead. In general it is best not to force ntpd to use specific poll intervals, allowing it to choose the best intervals based its current needs and the quality of the available servers and the clock. In some cases it may not be practical for ntpd to run con- tinuously. In the past a common workaround has been to run the ntpdate program from a cron job at designated times. However, ntpdate does not have the crafted signal process- ing, error checking and mitigation algorithms of ntpd. The ntpd daemon with -q option is intended to replace ntpdate when used in this manner. Setting this option will cause ntpd to exit just after setting the clock for the first time. The procedure for initially setting the clock is the same as in continuous mode; most applications will probably want to specify the iburst keyword with the server confi- guration command. With this keyword a volley of messages are exchanged to groom the data and the clock is set in about 10s. If nothing is heard after a couple of minutes, the dae- mon times out and exits. Eventually the ntpdate program may be retired. Kernel Clock Discipline The kernel supports a method specific to ntpd to discipline the clock frequency. First, ntpd is run in continuous mode with selected servers in order to measure and record the intrinsic clock frequency offset in the frequency file. It may take some hours for the frequency and offset to settle down. Then ntpd is run in normal mode as required. At each startup, the frequency is read from the file and initializes the kernel frequency, thus avoiding the settling period. When the kernel discipline is in use, the system's clock is adjusted at each system tick and thus the system clock is always as accurate as possible. When the kernel discipline is not used the clock is adjusted once each second. It is important to delete the ntp.drift file before starting ntpd if the intrinsic frequency might have changed, such as by a motherboard swap. Poll Interval Control The ntpd program includes an intricate clock discipline to reduce the network load while maintaining a quality of syn- chronization consistent with the observed jitter and wander. There are a number of ways to tailor the operation in order to enhance accuracy by reducing the interval or to reduce network overhead by increasing it. However, the user is advised to carefully consider the consequences of changing the poll adjustment range from the default. It is not the case that shorter poll intervals will necessarily lead to more accuracy. Most device drivers will not operate properly if the poll interval is less than 64 s and that the broad- cast server and manycast client associations will also use SunOS 5.11 Last change: 12 Apr 2007 3 System Administration Commands ntpd(1M) the default, unless overridden. In general, it is best to let ntpd determine the best polling interval. In some cases involving dial up or toll services, it may be useful to increase the minimum interval to a few tens of minutes and maximum interval to a day or so. Under normal operation conditions, once the clock discipline loop has stabilized the interval will be increased in steps from the minimum to the maximum. However, this assumes the intrinsic clock frequency error is small enough for the discipline loop correct it. The capture range of the loop is 500 PPM at an interval of 64s decreasing by a factor of two for each doubling of interval. At a minimum of 1,024 s, for example, the capture range is only 31 PPM. The Huff-n'-Puff Filter In scenarios where a considerable amount of data are to be downloaded or uploaded over bandwidth limited links, time- keeping quality can be seriously degraded due to the dif- ferent delays in the two directions. In many cases the apparent time errors are so large as to exceed the step threshold and a step correction can occur during and after the data transfer is in progress. The huff-n'-puff filter is designed to correct the apparent time offset in these cases. It depends on knowledge of the propagation delay when no other traffic is present. The filter maintains a shift register that remembers the minimum delay over the most recent interval measured usually in hours. Under conditions of severe delay, the filter corrects the apparent offset using the sign of the offset and the difference between the apparent delay and minimum delay. The name of the filter reflects the negative (huff) and positive (puff) correction, which depends on the sign of the offset. The filter is activated by the tinker command and huffpuff keyword, as described in the Miscellaneous Options page at file:///usr/share/doc/ntp/miscopt.html. Leap Second Processing As provided by international agreement, an extra second is sometimes inserted in Coordinated Universal Time (UTC) at the end of a selected month, usually June or December. The National Institutes of Standards and Technology (NIST) pro- vides an historic leapseconds file at time.nist.gov for retrieval via FTP. This file, usually called ntp- leapseconds.list, is copied into the /etc/inet directory and the leapfile configuration command then specifies the path to this file. At startup, ntpd reads it and initializes three leapsecond values: the NTP seconds at the next leap event, the offset of UTC relative to International Atomic Time (TAI) after the leap and the NTP seconds when the SunOS 5.11 Last change: 12 Apr 2007 4 System Administration Commands ntpd(1M) leapseconds file expires and should be retrieved again. If a host does not have the leapsecond values, they can be obtained over the net using the Autokey security protocol. Ordinarily, the leapseconds file is installed on the primary servers and the values flow from them via secondary servers to the clients. When multiple servers are involved, the values with the latest expiration time are used. If the latest leap is in the past, nothing further is done other than to install the TAI offset. If the leap is in the future less than 28 days, the leap warning bits are set. If in the future less than 23 hours, the kernel is armed to insert one second at the end of the current day. Additional details are in the The NTP Timescale and Leap Seconds white paper at http://www.eecis.udel.edu/~mills/leap.html. If none of the above provisions are available, dsependent servers and clients tally the leap warning bits of surviving servers and reference clocks. When a majority of the sur- vivors show warning, a leap is programmed at the end of the current month. During the month and day of insertion, they operate as above. In this way the leap is is propagated at all dependent servers and clients. OPTIONS -4, --ipv4 Force DNS resolution of following host names on the command line to the IPv4 namespace. Cannot be used with the --ipv6 option. -6, --ipv6 Force DNS resolution of following host names on the command line to the IPv6 namespace. Cannot be used with the --ipv6 option. -a, --authreq Require cryptographic authentication for broadcast client, multicast client and symmetric passive associa- tions. This is the default. This option must not appear with authnoreq option. -A, --authnoreq Do not require cryptographic authentication for broad- cast client, multicast client and symmetric passive associations. This is almost never a good idea. This option must not appear with the authreq option. -b, --bcastsync Enable the client to sync to broadcast servers. SunOS 5.11 Last change: 12 Apr 2007 5 System Administration Commands ntpd(1M) -c string, --configfile=string The name and path of the configuration file, /etc/inet/ntp.conf by default. -d, --debug-level Increase output debug message level. This option may appear an unlimited number of times. -D string, --set-debug-level=string Set the output debugging level. Can be supplied multi- ple times, but each overrides the previous value(s). -f string, --driftfile=string The name and path of the frequency file, /var/ntp/ntp.drift by default. -g, --panicgate Allow the first adjustment to exceed the panic limit. Normally, ntpd exits with a message to the system log if the offset exceeds the panic threshold, which is 1000s by default. This option allows the time to be set to any value without restriction; however, this can happen only once. If the threshold is exceeded after that, ntpd will exit with a message to the system log. This option can be used with the -q and -x options. See the tinker configuration file directive for other options. -k string, --keyfile=string Specify the name and path of the symmetric key file. /etc/inet/ntp.keys is the default. -l string, --logfile=string Specify the name and path of the log file. The default is the system log file. -L, --novirtualips Do not listen to virtual IPs. The default is to listen. -m, --mdns Register as a NTP server with mDNS system. Implies that you are willing to serve time to others. -n, --nofork Do not fork. -N, --nice To the extent permitted by the operating system, run ntpd at the highest priority. SunOS 5.11 Last change: 12 Apr 2007 6 System Administration Commands ntpd(1M) -p string, --pidfile=string Specify the name and path of the file used to record ntpd's process ID. -P number, --priority=number To the extent permitted by the operating system, run ntpd at the specified sched_setscheduler(SCHED_FIFO) priority. -q, --quit Set the time and quit. ntpd will exit just after the first time the clock is set. This behavior mimics that of the ntpdate program, which is to be retired. The -g and -x options can be used with this option. Note: The kernel time discipline is disabled with this option. -r string, --propagationdelay=string Specify the default propagation delay from the broadcast/multicast server to this client. This is necessary only if the delay cannot be computed automat- ically by the protocol. -s string, --statsdir=string Specify the directory path for files created by the statistics facility. This is the same operation as the statsdir statsdir command. -t number, --trustedkey=number Add a key number to the trusted key list. This option can occur more than once. This is the same operation as the trustedkey key command. -U number, --updateinterval=number interval in seconds between scans for new or dropped interfaces. This option takes an integer number as its argument. Give the time in seconds between two scans for new or dropped interfaces. For systems with routing socket support the scans will be performed shortly after the interface change has been detected by the system. Use 0 to disable scanning. 60 seconds is the minimum time between scans. --var=nvar make ARG an ntp variable (RW). This option may appear an unlimited number of times. --dvar=ndvar make ARG an ntp variable (RW|DEF). This option may appear an unlimited number of times. SunOS 5.11 Last change: 12 Apr 2007 7 System Administration Commands ntpd(1M) -x, --slew Slew up to 600 seconds. Normally, the time is slewed if the offset is less than the step threshold, which is 128 ms by default, and stepped if above the threshold. This option sets the threshold to 600 s, which is well within the accuracy window to set the clock manually. Note: Since the slew rate of typical Unix kernels is limited to 0.5 ms/s, each second of adjustment requires an amortization interval of 2000 s. Thus, an adjustment as much as 600 s will take almost 14 days to complete. This option can be used with the -g and -q options. See the tinker configuration file directive for other options. Note: The kernel time discipline is disabled with this option. -?, --help Display usage information and exit. -!, --more-help Extended usage information passed thru pager. --version Output version of program and exit. OPTION PRESETS All of the above options except the last three may be preset by loading values from environment variables named: NTPD_ or NTPD The environmental presets take precedence (are processed later than) the configuration files. The option-name should be in all capital letters. For example, to set the --quit option, you would set the NTPD_QUIT environment variable. AUTOMATIC SERVICE MANAGEMENT (SMF) NTP on Solaris is managed via the service management facil- ity described in smf(5). There are several options controlled by services properties which can be set by the system administrator. The available options can be listed by executing the following command: svccfg -s svc:/network/ntp:default listprop config Each of these properties can be set using this command: svccfg -s svc:/network/ntp:default setprop propname = value The available options and there meaning are as follows: config/debugfile A string specifying the location of the file used to log debug output, when debugging is turned on. The default is /var/ntp/ntp.debug. SunOS 5.11 Last change: 12 Apr 2007 8 System Administration Commands ntpd(1M) config/debuglevel An integer specifying the level of debugging requested. A zero means no debugging. The default is zero. config/logfile A string specifying the location of the file used for log output. The defualt is /var/ntp/ntp.log config/no_auth_required A boolean which when true, specifies that anonymous servers such as broadcast, multicast and active peers can be accepted without any pre-configured keys. This is very insecure and should only be used if the nework is secure and all the systems on it are trusted. The defualt is false. config/slew_always A boolean which when true, instructs ntpd to slew the clock as much as possible, instead of stepping the clock. It does not prevent all stepping, but increases the threshold above which stepping is used. It also disables the use of the kernel NTP=fP facility, which is incompatible with long slew times. The default is false. config/wait_for_sync A boolean which when true, causes the NTP service to delay coming completely on-line until after the first time the system clock is synchronized. This can pote- tially delay the system start up by a significant amount. The default is false. config/mdnsregister A boolean which when true, will cause the daemon to register with the network mDNS system. The default is false. config/verbose_logging A boolean which when true, cause the daemon to issue logging messages. The default is false. NOTES The system clock must be set to within 68 years of the actual time before ntpd is started. The ntpd service is managed by the service management facil- ity, smf(5), under the service identifier: svc:/network/ntp:default Administrative actions on this service, such as enabling, disabling, or requesting restart, can be performed using SunOS 5.11 Last change: 12 Apr 2007 9 System Administration Commands ntpd(1M) svcadm(1M). The service's status can be queried using the svcs(1) command. In contexts where a host name is expected, a -4 qualifier preceding the host name forces DNS resolution to the IPv4 namespace, while a -6 qualifier forces DNS resolution to the IPv6 namespace. Various internal ntpd variables can be displayed and confi- guration options altered while the ntpd is running using the ntpq and ntpdc utility programs. When ntpd starts it looks at the value of umask, and if zero ntpd will set the umask to 022. Source for ntpd is available on http://src.opensolaris.org. The documentation available at /usr/share/doc/ntp is pro- vided as is from the NTP distribution and may contain infor- mation that is not applicable to the software as provided in this partIcular distribution. ATTRIBUTES See attributes(5) for descriptions of the following attri- butes: ____________________________________________________________ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |_____________________________|_____________________________| | Availability | SUNWntpu | |_____________________________|_____________________________| | Interface Stability | Uncommitted | |_____________________________|_____________________________| SEE ALSO svcs(1), sntp(1M), ntp-keygen(1M), ntpdate(1m), ntpq(1M), ntptrace(1M), ntptime(1M), svcadm(1M), ntpdc(1M), rename(2), attributes(5), smf(5) SunOS 5.11 Last change: 12 Apr 2007 10